Posts

Second Year: Extra Credit Project

Image
Second Year: Extra Credit Project Storage Shelves   First I cleaned the area the shelves were going. Next I was laying out where the shelves were going. I used four 2x4s for the legs of the shelves. I cut the legs to 5' so there is enough space on the top to put boxes. With a 5' you can get two 20" equal spaces. The storage totes are about 16 1/12" so I chose to have 20" spaces so there is enough room to get your hands in the space to grab em. Next, I transferred the layout onto the other three legs.  Now I lined up the three shelves on their sides to begin attaching the legs.  Right here I'm flushing up the top shelve with the leg and then I squared up the legs with the shelve so it'll sit properly. I screwed the legs on the edge of shelves with four 3 1/2" screws. Once I did one side I flipped the whole unit over to attach the other two legs. Now that the legs were on I stood the unit up and slid it over to the wa...

Second Year Interior Finish Blog:Week 21

Image
Second Year Interior Finish Blog Week 21: Tuesday-Mar 10: Today I was working on attaching the nosings to the treads. I spaced the pocket screw holes so the balusters would land in between them. Once that was done, I glued the nosing and clamped it to the tread and then pocket screwed them.  Thursday-Mar 12:(Mid-Term)

Second Year Interior Finish Blog:Week 20

Image
Second Year Interior Finish Blog Week 20: Tuesday-Mar 3:   Today I was working on the finish treads. Once I cut the treads to the rough measurement, I set up a jig that clamps all the treads together. This is so the nosing slot that I cut out is all equal.  Thursday-Mar 5:  Today I working on the nosings. I ripped some 11/4" strips on the table saw.

Second Year Interior Finish Blog:Week 19

Image
Second Year Interior Finish Blog Week 19: Tuesday-Feb 25: Today I worked on building my routing jig for the skirt boards. This will be used for routing out a slot for the treads and risers to go in. I just used plywood scraps and short screws. Thursday-Feb 27:    Today I worked on the housed skirt board. I planed it and laid it out on the board.

Second Year Interior Finish Blog:Week 18

Image
Second Year Interior Finish Blog Week 18: Tuesday-Feb 18: Today I was working on milling the handrails for the utility/finish stairs and creating a rosette for the handrail to attach to. I cut two small blocks in the shape of an octagon and then I routed the edges to give it a decorative look. Next I Attached the rosette and the hardware to a stud in the wall on the top and bottom of where the handrail was going to be located. Once that was done, I measured up from the treads where I wanted the bottom edge of the handrail to be. To keep the measurement plumb I held a level with the tape measure as shown in the picture.  Thursday-Feb 20: Today I worked on planing the outside skirt board and gluing up the housed skirt board for the finish staircase.

Second Year Interior Finish Blog:Week 17

Image
Second Year Interior Finish Blog Week 17: Tuesday-Feb 11:   Today I worked on laying out both the outside and housed skirtboard. Laid them out, cut them and then fastened them to the stairs. Thursday-Feb 13:   Today I was working on the handrail. Grabbed a rough board from above and planed/jointed it and ripped 2 5/8" strips on the table saw.

Second Year Interior Finish Blog:Week 16

Image
Second Year Interior Finish Blog Week 16: Tuesday-Feb 4: Today I got the carriage fastened to the platform and the treads and risers. When screwing on the treads and risers, Start at the bottom and work your way up as shown in the pictures. Being sure to put a couple screws in each riser. Once all the treads and risers were on, I then ripped some plywood for the top of the platform and screwed it down. Thursday-Feb 6: Today I was working on the finish treads and risers. I grabbed a board from above and planed it and jointed it. Next I ripped pieces to about 3 or so inches to have the total width be 12". Then I glued 4 together each to make 6 treads.